Wand Stand

Color: Black

Sale price£3.50

Tax is only included for UK purchases. Shipping calculated at checkout

Free Shipping

From £49 to the UK or £199 Worldwide

Provides increased stability for the Wand and creates a small gap to prevent the hot glass adapter from touching the surface below. You can also use your Wand on its side. It’s a friction fit and might mark the Wand slightly during installation. 3D printed plastic. Keep away from direct sunlight and high temperatures.

 

iSpire Wand not included. 

Customer Reviews

Based on 7 reviews
100%
(7)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
R
Ryan S.
Wand stand

The wand stand is a must have for at home use with the wand. The cup gets very hot, and this stand keeps the hot glass off my wood table. The tempest ecosystem is so thought out, and this is just another simple yets great idea.

R
Robb
Perfect attachment

Didn't get a stand with my Tempest so bought separately; ideal attachment for the wand.

B
Ben C.
Simple but effective

Highly recommend adding this to your Wand to increase stability and to avoid any risk of scorch marks.

E
E.J.
Wand stand, a must have

It was offered at the release with the Tempest Kit, batch 1.
Make the use with the Wand more hands free, with a slightly larger footprint as a trade-off.

Doesn't need to take it off for accessing the Wand battery door.
It can be installed correctly when pointing the small black arrow on the battery door side, and sliding it aligned with the power/switch button.

Love the "on the side position" for reducing the risk of small herb bits to fall on the Ball Retaining screen, when I miss my tamping job.
Highly recommended for Wand use on any desk/table.
As the Wand glass adapter and the Reload, it's one of MH accessories who make the Tempest user experience so nicer.

The 3D print material doesn't like heat or sunlight and could break with a bad fall, don't take it on expedition.
For outdoors, I don't take the W stand and simply put the Wand screen side to the ground after a heating cycle.
One stand makes the Wand not flat on the surface anymore, and it functions very well like that, but some users prefer using two W stands to make the Wand leveled again.

Some Wand IH tips:
The temperature on the screen doesn't manage any temperature control in any way, it only defines a timer limit to the heating cycle.
The small thermocouple white wire next to the induction coil is only for the device overheat protection.
Do not adjust the Wand temperature/timer while the device is already heating, it will mess with Fahrenheit value when on the Celsius degree temp.

Battery gauge on the Wand screen doesn't really show the autonomy left, but instead shows the voltage of the batteries in real-time.
One battery bar (3.7V) can still do a few more heat cycles. The Wand cut off is when each battery is down to 3.5 volts.

When the Wand orange light stops blinking and stays on, the time remaining before the "Time out" screen message is always 15sec.
During this 15sec, the Wand is still heating, but at a much lower power.
The same happens when the Wand is on flower mode (green light), except that the time is always 10sec.

The power is higher when the batteries are fully charged, it reduces the heating cycle time.
For more consistent results with the timer and better battery longevity, I swap batteries when there is one bar left (3.7V) on the screen while the Wand is cold/rest.
With old 2020 Samsung 25R batteries, I get about 6 heat cycles from a room temp Tempest until 3.7V, and 10 heat cycles until the Wand 3.5V cut off.

The power delivery of the Wand depends on the vaporizer mass inserted, the heat cycle time (temp) chosen, and the battery voltage.
A Dynavap will draw less power than the Wand concentrate cup or the Tempest, for example.
A 260°C heat cycle will be shorter than a 360°C.
A 300°C heat cycle at full battery voltage is shorter than the same cycle at low battery.

Autonomy is related to the pair of 18650 batteries chosen.
These 18650 high discharge lithium batteries have great power, but offer no compromise with security, please do your safety homework.
Choose a minimal 20A Current Discharge Rating before any autonomy capacity specs.

USB C battery charging on the Wand isn't recommended, for emergency only, as this charging method will create an unbalanced battery voltage.
Always paired the same 18650 together, as they need to age at the same rate.
Charging in a proper external charger is essential, and multiple 18650 pairs will handle autonomy for the heavy users.

Batch 2 future Wand IH users, don't forget to get the Wand glass adapter and a Wand stand, you will need them.

J
Jason P.
Perfect for the job

It's such a useful stand. Slightly different from the one that came with the Tempest. I got it so with the 2, the Wand is flat whilst raised. Everything is so well thought out from Mad Heaters. Great product and great company. Would recommend both to anyone. 5 stars all round 👍

I
Ignacio F.
Great fit.

Perfect add-on for The Wand to make it totally stable on my desk BUT... you need to BUY TWO of them if you want it to stay flat (as i did). No big deal because it's an inexpensive accessory.

A
Anonymous
Get it!

Amazing addition to the wand!